JETech Screen Protector for iPhone SE 3/2 (2022/2020 Edition) 4.7-Inch, Tempered Glass Film, 3-Pack

I haven't used any other brand of phone cover so can't really compare but these are easy to use and don't retain any air bubbles if you follow the instructions to the letter e.g. let the cover do the work attaching itself to the phone. I do feel they have protected my phone well on the couple of occasions I have dropped it!

Great quality product. I purchased these for my mum to use on her phone and ended up getting roped into applying it. They are very easy to apply, the adhesion to the screen is good and they perform well. Her phone is thrown about in her bag on a daily basis and there’s no sign of wear and tear to the screen cover.Doesn’t affect the performance of the screen, there’s no lag or delay with the touch sensitivity.They do a great job of protecting the phone screen from being scratched because even in phone cases and in bags, dust and small particles of dirt can still scratch the screen. Looks great and you can’t even tell it’s on the phone.

I replace these screen protectors every few weeks in our house as invariably someone drops their phone and the protector smashes. I have given a 4 star as although I think the product is good, I would expect it to last longer than one drop of the phone.

Really pleased with the finished result. No bubbles. Perfectly clear screen. Touch all works fine. Only needed one of the 3 screens provided. Yes it is a smaller than the full glass area, but it has to be, because the phone's glass front curves away. But the fit is that good it almost looks like the phone's glass was manufactured that way.Needless to say, my suggestions here are in addition to the instructions that come with it!First thing I did was to check I had the correct part, given the packaging does not say what phones they are for. If you check the original Amazon description, the part specific to iPhone SE 2020 has a part number starting 0807, whereas the older iPhone 7/8/SE part has a part number starting 0806, so be sure you have the 0807 part.When it comes to fitting the protector, preparation is key. I used a freshly cleaned tray, with some kitchen towel on it, and with all the bits to hand. And I made sure to do it at a time when I was not pushed for time; this is not a job to feel you need to rush at!One thing I did that the instructions don't tell you, was to clean the BACK of the phone, to be sure the hinge stickers stay stuck on properly while you need them to. Did this with the cleaning swab and drying off cloth that comes with the kit. The hinge stickers stayed firmly stuck in place all the time I needed them to.Then with hinge stickers in place on the back, and with the screen protector aligned on the top, ensure to keep the hinge tapes slack-free when pulling them round and sticking across onto the protector; just tight enough to ensure no slack. Once the hinges are on, then double check - gently pull the screen protector to the left (assuming hinges on right) against the hinges, and check it is aligned spot on. For alignment I used the slotted hole at the top and the home button cut-out at the bottom. If not quite right then just adjust the hinge positions until OK.Once the phone's screen is dust free as per instructions, then after removing the protective strip, you can just lay the screen down, pulling to the left against the hinges as you do so - if you did the previous bits OK then it will be lined up perfectly.Yes there will be bubbles, but no worries - they are easy to sort and no need to rush when sorting them. As the instructions say, just gently lift corners, then smooth the bubbles back out towards the corners again. Took a few goes in some cases, but it did work well.Very pleased with the finished result. Been in my pocket a few days now, with no sign of any scratches so far.

Good quality screen saver. Easy to apply.

This fits well to an iPhone SE and although it doesn’t cover 100% of the screen, it is more than adequate if you have a case fitted.As with all protectors, it is vital to ensure the underlying screen is as clean as possible. I use compressed air just to blow the dust off should it land during fitting. Also key is to have a good light source that you can light the screen from the side to see any dust.There were some small bubbles after fitting however these went away after a day or so. Larger ones I forced out to the edges.How long it will last I don’t know. The phone is being used by an elderly relative who ‘jabs’ the screen rather than just touch it. Worth the money and no loss of touch.

I’ve had screen protectors before where the protector is in a box that aligns it to your phone for you, so I was surprised to find you have to use stickers to manually align this one. Miraculously, I managed to align it quite well, but it was a bit stressful. There was an air bubble remaining, so I lifted the corner as suggested and managed to get it out no problem. The package comes with three protectors, which I hadn’t realised. I hope I only ever need this one.

I decided to try the privacy screen this time. It works fine but the privacy is achieved by putting thousands of tiny dots on the screen. This darkens the screen slightly and it’s rather like looking at newsprint through a magnifying glass. I might go back to a plain screen as the privacy is not all that important really. Just thought I would give it a try and found that it has its drawbacks.